Large Scale Central

C.V.S.Ry. Rockhill Shop Division

Thank you Fred. I appreciate your concern and I have had those thoughts as well. Our bedrooms have no direct exit (except windows near ground level), although the house does have two doors. There is no local code or ordinance that applies as this is still considered an outbuilding, which are unregulated here.

Regarding the gas, if you have seen news items of any of the recent home explosions, having a second exit would be meaningless in an explosion. A regular fire is a different situation. A propane detector should be high on my priority list as well as a good sized ABC extinguisher. Any fire to start while I am in it would likely begin small and a good extinguisher would at least provide an escape if needed.

The electricity is an extension cord, albeit a big one, plugged in to an outdoor GFCI. It can be quickly disconnected in an emergency. Again, no code compliance required because it is considered temporary power, like an RV. I did, however, follow NEC code when wiring the shop. There was no requirement for inspection.

I’m not going to loose any sleep over it :smiley:

Just make sure if you put it in your camper, then cross the border with the extinguisher, you shouldn’t tell them that you have fire arms.

Great weather for working outside, even if it’s a bit windy. I am pre-cutting all the trim. I will paint it all indoors before installation. The angle of the header is too sharp for my mitre gauge so I had to free hand guide it on the table saw. I was able to use the drops against the fence to guide the second one. Here is the dry fit of a header…

The two small windows and the corners are cut. Now on to the front window.

1 Like

With time off to work on the 1:1 railroad it took nearly a week to fabricate and pre-paint all the trim, but it’s done. Yesterday was install day. This completes all the trim that needed to be made.

West side and front…

Front with a window close up…

East (RR) side with a window close up…

Yet to do is paint the door then hang those signs and some earthquake bolts.

4 Likes

Turned out looking great Jon.

Earthquake Bolts???

Brick buildings often featured steel roods between walls to help keep the walls moving together. They terminated outdoors with a plate, often decorative. I was tasked 20 some years ago with sourcing replicas for a building my company was building. I found resin replicas of cast iron stars that I had them add a large bolt and square nut to the end. I ended up with the 5 extras that were ordered “in case”.

This was a prototype example…

What we came up with…

2 Likes

Jon,
I understand earthquake bolts and their application, I just don’t really understand their application in a place like Pennsylvania, Oh decoration only, OK I get it finally.

They were common in New England. I’ve not looked for examples here, but I would think they might be too, but not on wooden buildings! But its my RR (building), so my rules :smiley:

So yes, seeing as they are fake, decoration only. I have 5 of them, at least 4 will find homes on the long walls. When we installed them on the new building, adhesive was used. I want them removable so I’ll drill the center and use one long screw.

1 Like

Jon;

I’ve seen many of those supports on brick buildings in Lebanon County and the Cornwall area in Pennsylvania. I believe they were intended to strengthen the brick walls of the building. Shapes included circles, stars, and what resembled a large letter S.

Best, David Meashey

1 Like

The East (RR) side decorations are up…

Those three on the ground go on the front, eventually!

3 Likes

Let me know your next vacation so I can borrow a couple signs for a little while.

Thanks for explaining the stars Jon, I thought they were mini versions of PA Dutch barn hex signs.

I installed the remaining 3 signs on the front. The shop sign still needs vinyl…

I was going to paint the door trim today, but it’s too humid :tired_face:

1 Like

I finaly had both time and good weather to finish painting the door and trim. I added one more star. It’s done until I decide to make the sign…

3 Likes

Jon, it’s looking so great. Just like your original renderings, but better.

1 Like

You need an emploies only sign on the door… :grin:

Ya know, you could always pick out the six panels on the door in your trim color.

Just saying
:rooster:

I’m with Rooster. Maybe a little black pinstriping around the panels. And window painted to match the door.

And, with only a few more tweaks…

OK, totally just kidding about that second one… :grin:

I might consider the panels, but the window is vinyl and it’s not getting painted. However, we are now in get a lot of crap done before winter mode, so not this year. I’d also like to make a new header for the door to match the window without removing the brickmold part of the pre-hung door. I need to measure and sketch it out to see if there is enough room.

In your AI fantasy, at least you added a second door to satisfy Fred!

Edit to add: Marilyn really liked the AI version until I told her the door alone was about $2K!