Forums General For Sale/Trade
  • Topic: WTB Bachmann Jumper PC Board

    Back To Topics
    (0 rates)
    • February 25, 2021 3:39 PM EST
      • PLEASANT GROVE, Utah
         
      • Posts
        3
      • Thanks
        0
      • Thanked
        2

      WTB Bachmann Jumper PC Board

      Looking for a spare jumper/dummy wiring card for the Bachmann J1/J2 plugs.

      Wiring up a Railpro receiver and would ideally like to use the dummy board. I have a Mogul from Bachmann that came with the card in the box. Recently picked up a used Bachmann K27, which has no dummy card and I found out Bachmann doesn't sell it as a spare part. (go figure...)

      I know I can solder directly to the solder pads, (and may do that) but thought I'd see if I can find a jumper/dummy card someone isn't using.

      Thanks,

      -Jay

    • February 25, 2021 3:52 PM EST
      • Your Host in Littleton, MA
         
      • Posts
        8,016
      • Thanks
        599
      • Thanked
        1,687

      This?

       

      ____________________________________

      Bob, your Site Host and Benevolent Dictator.

    • February 25, 2021 4:02 PM EST
      • Fort Myers Beach & Annapolis, Florida & Maryland
         
      • Posts
        2,950
      • Thanks
        175
      • Thanked
        725

      Call the Bachmann Parts Dept in Philadelphia. They often have stuff lying around from returned locos.

      ____________________________________

       

        Pete

    • February 27, 2021 11:26 AM EST
      • Candlewood Valley, Connecticut
         
      • Posts
        14,102
      • Thanks
        1,807
      • Thanked
        1,342

      If you haven't found one yet, let me know. I may have a second one laying around. I want to keep at least one on hand to check out any future Bachmann Plug-N-Play purchases before ripping the guts out!

      ____________________________________

      www.cvsry.com www.cvsry.com

    • February 28, 2021 7:33 AM EST
      • Chelmsford, MA
         
      • Posts
        726
      • Thanks
        48
      • Thanked
        176

      I have lots of the bachmann dummy boards similar to the one Bob posted a photo above. should you need one.

       

      The easier board to use is the dummy board with wires as it is already set up for this.

       

      Unfortunately this board is a little harder to find.

       

      Stan

    • February 28, 2021 12:57 PM EST
      • PLEASANT GROVE, Utah
         
      • Posts
        3
      • Thanks
        0
      • Thanked
        2

      Thanks for the advice. The board Bob took a picture of is a little different by could probably work. The one I’m familiar with was as Stanley mentioned already setup with wires coming off. Beggars can‘t be choosers in these situations, I’ll reach out directly and report back here on what works out. Thanks again.

    • February 28, 2021 8:12 PM EST
      • Candlewood Valley, Connecticut
         
      • Posts
        14,102
      • Thanks
        1,807
      • Thanked
        1,342

      Jay and I have connected. I have a new-in-bag spare with wires. Hopefully he will be all set.

      ____________________________________

      www.cvsry.com www.cvsry.com

    • February 28, 2021 8:15 PM EST
      • Candlewood Valley, Connecticut
         
      • Posts
        14,102
      • Thanks
        1,807
      • Thanked
        1,342

      Bob McCown said:

      This?

       

       

      Stan - please correct me if I am wrong, but isn't that the DC jumper board used to run off track power?  I'm sure those solder pads could be used, along with the switchecs on the main board, but as Stan noted - the one with the wires is ready to go.

      ____________________________________

      www.cvsry.com www.cvsry.com

    • March 1, 2021 12:22 AM EST
      • South Dartmouth , Massachusetts
         
      • Posts
        144
      • Thanks
        136
      • Thanked
        68

      I bought one of the climax locos during trainworlds $199 special. I run track power and soldered in a Phoenix sound system to the board shown. I have the plug in board with the wires that I’ll probably never use.

Forums General For Sale/Trade

    Icon Legend

  • Topic has replies
    Hot topic
    Topic unread
    Topic doesn't have any replies
    Closed topic
    BBCode  is enabled
    HTML  is enabled

Add Reputation

Do you want to add reputation for this user by this post?

or cancel

Ads by Google