Forums Modeling Motive Power
  • Topic: Mason Bogie

    Back To Topics
    (0 rates)
    • June 18, 2019 6:37 PM EDT
      • Ormond Beach, Fl. 32174
         
      • Posts
        596
      • Thanks
        3
      • Thanked
        265

      cylinders from the front

      new update on the Mason Bogie project: decided to keep the orange stripe on the side of the tender then messed around for naming on the side of it, wanted my The Falls with progressing downward flow like my other tenders but rivets and silhouette lettering don't mix and that are is full of rivets, then printed words coquina falls in two different lines and installed above and below the rivets and still didn't ring my bell, was trying to simulate Breckenridge, Tenmile, etc. but just didn't work out, but did find a picture of one that had a large engine # in that area and am now working on a stencil so I can paint it on. Been working on the cylinders and although the spreewald engine that I'm using for the drive had round cylinders the upper valve part didn't look anything like walschaerts valve gear I made one to fit on top of their round cylinders using the tops to a old battery powered Bachmann set that I had. Surprisingly the spreewald plastic for their cylinders is model masters compatible and bonded great. Now the side rods and valve gear isn't quite the correct kind but close enough for me + the tops for the cylinders were a little large but fit nice and really don't look out of place, you know me not a rivet counter but like rivets which will be added later. will up date this thread when more is done, Billspreewald clyinders    cylinders from the rear

    • June 20, 2019 10:34 AM EDT
      • Ormond Beach, Fl. 32174
         
      • Posts
        596
      • Thanks
        3
      • Thanked
        265

      More done on the Mason Bogie project and was able to get the Lionel cowcatcher placed and attached to the frame  cowcatcher from the frontcowcatcher from the side

    • June 20, 2019 5:30 PM EDT
      • Pittsburgh, Pennsylvania
         
      • Posts
        10,652
      • Thanks
        95
      • Thanked
        746

      So, how does the drive assembly swivel when its all mounted to one frame?

      ____________________________________

      Shannon car Shops
      Home of the infamous leg lamp

      I.A.R.R.R. Member #12

      and King Butt Modeler

    • June 21, 2019 6:22 PM EDT
      • Missouri, It's like Floodsburg, man
         
      • Posts
        2,548
      • Thanks
        245
      • Thanked
        282

      David Maynard said:

      So, how does the drive assembly swivel when its all mounted to one frame?

      If you can find a copy of this it will answer that,

      Oh, you were probably asking about the model, well, anyway, the book is worth reading.

    • July 31, 2019 12:20 PM EDT
      • Ormond Beach, Fl. 32174
         
      • Posts
        596
      • Thanks
        3
      • Thanked
        265

      Moving along, got the cab, tender, cowcatcher, cylinders and rear bogie painted and all body parts screw together and on sub frame, now time to start planning the way to articulate itcowcatchertenter to body RSside pix

    • August 3, 2019 10:10 AM EDT
      • Ormond Beach, Fl. 32174
         
      • Posts
        596
      • Thanks
        3
      • Thanked
        265

      Mason bogie

      Don Watson said:

      Bill, if you haven't already done so, check out this site

      Thanks Don, yes David did unbelievable work, way above my skill level, I have seen most of what is on that site from (http://www.ross-crain.com/rr_dsp6e-fletcher.htm) site that I found some time ago, but it looks a little more user friendly that the ross-crain one that I used.  Biggest problem is the type of motor block I have chosen mainly because I had one and that being a LGB spreewald. The motors used by the master builders were vertical mounted and the LGB is horizontal meaning the motor block has a lot more bulk to it. This build is more of use what I have rather than everything is perfect. Certainly thank you for looking out for me, Bill  

       

      http://forums.mylargescale.com/27-masterclass-articles/20743-masterclasses-articles-index-downloads.html

       

      Look under the Mason Bogie build topic.  There's a wealth of information. You can see how Dave pivoted the drive mechanism.

       

      Doc

       

      X

      This post was edited by Bill Barnwell at August 3, 2019 10:12 AM EDT
    • August 3, 2019 12:34 PM EDT
      • Hendersonville, North Carolina
         
      • Posts
        244
      • Thanks
        32
      • Thanked
        58

      Bill,

       

      I understand your issues with using the existing drive.  In case you're interested, I do have a partially built laser-cut SS drive chassis with motor and all the parts necessary to complete the assembly of a close-to-scale drive mechanism.  The instructions are provided on the site mentioned before.

       

       

       

      I'd be willing to part with it for monetary compensation.

       

      Doc

    • August 3, 2019 2:06 PM EDT
      • Ormond Beach, Fl. 32174
         
      • Posts
        596
      • Thanks
        3
      • Thanked
        265

      Don I appreciate the offer and will keep it in mind, retired and on a budget and try to use what I have, that and I'm stubborn to the point of stupid. I spent 3 months trying to get a red LED to blink on the top of my city water tower just because I wanted it to work off of solar power. I use and have gotten pretty good with bashing store bought cheap solar powered pathway lights, Wal-Mart @ $.98, and had terrible problems with getting it to work because of the IC in the LED that made it blink. In the long run I was able to use part of it but not all, sad thing is I could have used a $3.00 one that I had but just had my mind set. Thanks again for the offer and help, Bill, That drive you have looks like a piece of art

      CWT

      This post was edited by Bill Barnwell at August 3, 2019 2:08 PM EDT
    • August 11, 2019 11:07 AM EDT
      • Ormond Beach, Fl. 32174
         
      • Posts
        596
      • Thanks
        3
      • Thanked
        265

      coming together

      Got a little more along on the mason bogie project, made the dome bases and they are now on there way to the paint shop, have the boiler running boards fitted and the upper section of the fire box adjusted and glued, now starting to look like an enginedome bases

      This post was edited by Bill Barnwell at August 17, 2019 7:02 PM EDT
    • August 17, 2019 4:33 PM EDT
      • Ormond Beach, Fl. 32174
         
      • Posts
        596
      • Thanks
        3
      • Thanked
        265

      quarter view from front

      quarter view from front

         Further progress on the mason bogie, boiler painted using cab light green and missed with silver over spray and the fire box I added rivets and colored both it and the smoke box with a dark gray metallic graphite. Pretty much most of the detailed fitting is done allowing a better look at the articulation suspension. which will be next along with the coloring of the running boards. Domes are done and screwed to the boiler with single 8/32 screw and leaving only the bell to be built and fitted to the top of the boiler. More to come, Bill 

      quarter view

    • August 17, 2019 6:45 PM EDT
      • Hendersonville, North Carolina
         
      • Posts
        244
      • Thanks
        32
      • Thanked
        58

      Looking good Bill. 

      Doc

    • August 18, 2019 9:51 AM EDT
      • Ormond Beach, Fl. 32174
         
      • Posts
        596
      • Thanks
        3
      • Thanked
        265

      Don Watson said:

      Looking good Bill. 

      Doc

      Thanks, Doc. Did you ever come up with a list of other parts you had?

    • August 18, 2019 11:59 AM EDT
      • Hendersonville, North Carolina
         
      • Posts
        244
      • Thanks
        32
      • Thanked
        58

      Bill,

      See private message. 

Forums Modeling Motive Power

    Icon Legend

  • Topic has replies
    Hot topic
    Topic unread
    Topic doesn't have any replies
    Closed topic
    BBCode  is enabled
    HTML  is enabled

Add Reputation

Do you want to add reputation for this user by this post?

or cancel

Ads by Google